Machines By Goldcrest
  • HOME
  • About
  • NEW MACHINES
    • FABERTEC CNC MACHINING CENTRES >
      • FABERTEC M1 CNC CENTRE ROUTER
      • FABERTEC M2 CNC CENTRE ROUTER
    • FABERTEC FIBER LASER CNC
    • FABERTEC CO2 LASER CNC >
      • FABERTEC L1 CO2 LASER CUTTER
      • FABERTEC L2 CO2 LASER CUTTER
    • VACUUM BLADDER PRESSES
    • WOODWORKING VACUUM PRESS
    • AUTOMOTIVE BLADDER VACUUM PRESS
    • SOLID SURFACE VACUUM PRESS
    • THERMOFORMING OVENS
    • PVC FOIL MEMBRANE PRESS
    • EDGE BANDING MACHINE
  • REFERENCES
  • Contact

BLADDER VACUUM PRESS FOR AUTOMOTIVE INTERIORS


Picture

​   The VPS3000AT is a bladder press based on our woodworking one VPS3000.

   As automotive interiors sector have a slightly different method of operation by using heat activated adhesives we introduced few important clever improvements to allow to cut pressing time to minimum.


   Infra Red Heating in the dome allows for almost rapid adhesive curing underneath the leathers, vinyls or other fabrics. It can heat up surfaces to approx 100C degrees.


  • Air circulation fans in the dome to prevent heat build up in any “dead space” and spread the heat evenly even if IR is heating surface of the membrane
  • Thermostat sensor is situated on the table as a long wire to allow to position it exactly on the mould giving operator accurate temperature reading. Also as an option extra sensors may be added to prepare 2/3/4 moulds in one cycle
  • As a option we are installing timer connected to thermostat. This allows to shut off heating after set number of minutes and prevent for example “over burning” of the adhesive or fabric - leather may dry to quickly creating unwanted stretch marks on surface
  • Option of 2mm or 3mm membrane. 2mm is much better for detailed mouldings if there is a need for plenty of details


TECHNICAL SPECIFICATION:


  • Working table dimensions (Model VPS3000AT): 2850mm x 1150mm or 2850mm x 1350mm (VPS3100AT)
  • Silicone membrane 800% max temperature: 220
  • Heater power, kW: 5
  • Vacuum Pump Pressure: -0,75bar
  • Vacuum Pump output, m3/h: 25
  • Operating vacuum, kg/cm2 (bar): - 0,85_0,90
  • Protection code: IP53
  • Noise level, Db: < 70
  • Voltage: 3Phase 400 50Hz
  • External dimensions, mm: length - 3150mm, width - 1350mm/1500mm, height - 1600mm
  • Weight, kg: 550
SHOP NOW
Picture
Picture
Picture
Picture



NEW MACHINES

FABERTEC CNC CENTRES ROUTERS
FABERTEC FIBRE LASER CNC​
FABERTEC CO2 LASER CNC

JOINERY VACUUM MEMBRANE PRESS
THERMOFORMING ACRYLIC VACUUM PRESS
AUTOMOTIVE INTERIORS BLADDER PRESS
THERMOFORMING OVENS
EDGE BANDING - EDGEBANDERS




TIMBER

European Oak
Steamed Beech
Siberian Larch
​Other, Walnut, Exotic

Support​​

Contact
​
Privacy Policy


© COPYRIGHT 2016.
​ALL RIGHTS RESERVED.
  • HOME
  • About
  • NEW MACHINES
    • FABERTEC CNC MACHINING CENTRES >
      • FABERTEC M1 CNC CENTRE ROUTER
      • FABERTEC M2 CNC CENTRE ROUTER
    • FABERTEC FIBER LASER CNC
    • FABERTEC CO2 LASER CNC >
      • FABERTEC L1 CO2 LASER CUTTER
      • FABERTEC L2 CO2 LASER CUTTER
    • VACUUM BLADDER PRESSES
    • WOODWORKING VACUUM PRESS
    • AUTOMOTIVE BLADDER VACUUM PRESS
    • SOLID SURFACE VACUUM PRESS
    • THERMOFORMING OVENS
    • PVC FOIL MEMBRANE PRESS
    • EDGE BANDING MACHINE
  • REFERENCES
  • Contact